Metal Gates and Fences in Naperville, IL

Most Naperville homes are single-family detached houses, so the usual need is a fenced backyard, a walk-through gate at the side of the house, or a gate across the driveway. Those homes often still have their original fences and gates. Older metal fences and gates there show real weather wear. Posts have shifted, latches no longer line up, and coatings have started to peel.

We handle new work and old work:

• Metal fence installation: steel, aluminum, and ornamental metal fencing, laid out to your lot and set on concrete footings.
• Driveway gate installation: single swing, double swing, and sliding gates sized to the opening and the slope of the drive.
• Pedestrian gate installation: walk-through gates with the swing direction, latch height, and self-closing hinges you need.
• Custom gate and fence fabrication: steel and aluminum frames, ornamental pickets, and decorative metalwork built from field measurements.
• Gate and fence repair: sag correction, hinge replacement, latch repair, weld repair, bent picket replacement, and loose post stabilization.
• Metal gate and fence refinishing: rust removal, surface preparation, primer, and a new exterior topcoat or powder coating.

We work across Naperville, from neighborhoods off Naper Boulevard and Naperville Road, out toward Springbrook Prairie and over toward McDowell Grove. We also serve nearby Lisle, Warrenville, and Plainfield.

Height is the first thing we check. A fence in Naperville cannot go over six feet. On a lot that runs along a major arterial road, the limit goes up to nine feet. We confirm which rule applies to your address before we order posts and panels, because a nine-foot post set where only six is allowed has to come back out.

The front and corner side yards follow a tighter rule. An open fence there can stand at the lot line only up to four feet. Corner lots get extra attention from us. We mark both street sides and keep picket spacing open so the fence counts as an open fence, then we size the gates to match that four-foot line.

Hobson Road has its own limit. Chain-link and board-on-board fences are not allowed along it. Aluminum and wrought iron are. That makes ornamental metal a natural fit for homes on Hobson Road, and we build those runs with open picket spacing and matching gates.

Around the Metra station and the Washington Street corridor in downtown Naperville, future redevelopment is planned. Gate swing clearance matters more on a narrow side yard. We measure the space a gate needs to open fully and switch to a narrower leaf, an outswing gate, or a sliding gate when the room is not there.

Age matters too. On an older fence, the ground around the posts has had time to settle. We check each post for lean and test the footings before we hang a new gate on old posts. A new gate on a loose post will sag again.

We start at your property with a tape and a level. We measure the run, the openings, and the grade. We check the existing posts, hinges, latches, and welds. Then we write up the work: what gets replaced, what gets repaired, and what gets refinished.

For a new fence, we lay out the line, mark post spacing, and dig the post holes. We set posts in concrete footings and keep them plumb while the concrete cures. On a slope, we use racked panels that follow the grade or stepped panels that stay level and drop at each post. We hang panels on brackets and check the picket line along the whole run.

For gates, we set hinge posts heavier than line posts because they carry the load. We weld or bolt hinge mounting plates square to the frame. We set the gate stops, drop rods, and latch so the gate closes on the same spot every time. We leave enough ground clearance for the gate to clear the driveway or walk without dragging.

For custom work, we build the gate or panels from field measurements. We cut the metal, weld the joints, and check the frame for squareness before installation. Then we fit it on site.

For repair, we find the cause first. A sagging gate can come from a leaning post, a worn hinge, or a cracked weld. We stabilize the post, replace the hinge, or reweld the frame, then realign the gate and latch. If water is trapped inside the tubing, we open a drain path so it can get out.

For refinishing, we remove the rust and failing coating by abrasive blasting or mechanical sanding. We degrease the metal, prime it, and apply an exterior topcoat or powder coating that bonds to the primer underneath. Paint over loose rust will peel again.

Can you fix my sagging gate or does it need to be replaced?

Most sagging gates can be fixed. We check the hinge post, the hinges, and the welds on the frame. If the post leans, we stabilize or reset it. If a weld has cracked or the frame has bent, we repair it. We recommend a new gate only when the frame itself is too far gone to hold square.

How tall can my metal fence be in Naperville?

Six feet in most yards. Lots along a major arterial road can go to nine feet. At the front or corner side yard lot line, an open fence can go up to four feet. We measure and confirm the rule for your lot before we order materials.

Can you match my existing fence?

Yes. We measure the picket size, picket spacing, rail height, and post size, then fabricate new panels or a gate to match. We refinish the new and old sections together when you want one finish across the whole run.

What affects the price?

Length of the run, the number and size of gates, steel or aluminum, custom fabrication, the grade, and the condition of existing posts all change the price. Our cost factors guide explains each one, and our project process guide walks through what happens from measurement to final adjustment.

Call (630) 473-9918 or request an estimate for metal gate and fence work in Naperville. Tell us what you see: a gate that drags, a latch that misses, a post that leans, or rust coming through the paint. We will measure the yard, check the posts and hardware, and put the recommended work in writing. You can also read more about our company.